ตัวกรองผลการค้นหา
I was on edge the whole time
แปลว่าฉันรู้สึกตื่นตระหนกมาตลอด
Burr Mashers
แปลว่า(english) Devices used to remove build up on edge of strip after the slitting process.
By-Pass
แปลว่า(english) Manual control used to by-pass automatic valve if it fails or in an emergency.
Looking For Trouble
Back Rake
แปลว่า(english) The angular surface ground back from the cutting edge of cutting tools. On lathe cutting tools. The rake is positive if the face slopws down from the cutting edge toward the shank, and negative if the face sloopes upward toward the shank.
Bevel
แปลว่า(english) Angle formed between the prepared edge of the end of tube and a plane perpendicular to the surface. Standard pipe bevel is 30 degrees.
Bandsaw
แปลว่า(english) A power saw, the blade of which is a continuous,narrow,steel band having teeth on one edge and passing over two large pulley wheels.
AIR BLEEDER AUTOMATIC
แปลว่า(english) A valve that is fit into a hydraulic pipeline to facilitate automatic release of air trapped in the pipeline. See also AIR BLEEDER, MANUAL.
วาล์ว
หมายถึงน. อุปกรณ์ชนิดหนึ่งในเครื่องยนต์ชนิดเผาไหม้ภายใน ทำหน้าที่เป็นลิ้นปิดเปิดเป็นจังหวะ ชุดหนึ่งเรียกว่า ลิ้นไอดี สำหรับให้อากาศหรืออากาศผสมนํ้ามันเชื้อเพลิงเข้าสู่ห้องเผาไหม้ อีกชุดหนึ่งเรียกว่า ลิ้นไอเสีย สำหรับให้แก๊สต่าง ๆ ที่เกิดจากการเผาไหม้ออกจากห้องเผาไหม้ไปสู่ท่อไอเสีย, ลิ้น ก็เรียก. (อ. valve).
Section Modulus:
แปลว่า(english) A property of a cross sectional shape, which depends on shape, and orientation. Section modulus is usually denoted S, and S = I/c, where I = moment of inertia about an axis through the centroid, and c is the distance from the centroid to the extreme edge of the section.
Burr
แปลว่า(english) The very subtle ridge on the edge of strip steel left by cutting operations such as slitting, trimming, shearing, or blanking. For example, as a steel processor trims the sides of the sheet steel parallel or cuts a sheet of steel into strips, its edges will bend with the direction of the cut.
Bent Axis Pumps
แปลว่า(english) In this pump, the pistons are at an angle to the drive shaft and Thrust Plate. The piston block shaft is connected to the drive shaft by a universal joint, not shown. The drive shaft, thrust plate, piston block shaft, and piston block all revolve. The connecting rods are attached to the thrust plate and revolve with it, unlike the swash plate pump where the piston rods slide past a stationary swash plate. The outlet ports are semi-circular holes in the Valve Plate, shown on the far right of the animation on edge and in a head-on view below, right. As the pump revolves, half the pistons suck in fluid as they pass over the intake port. The other pistons discharge their fluid through the outlet port. This pump should be compared to the radial piston pump, swash plate pump, and wobble pump.