ค้นเจอ 169 รายการ

Ball Piston Pumps

แปลว่า(english) The Ball Piston Pump is a very simple pump design. It has a rotor which revolves around an internal stator. The rotor has twelve cylinders machined out of it, and each cylinder has a ball inside which can slide in and out of the cylinder.

Bundle

แปลว่า(english) Specific number of sheets which equals 1 unit of production. Number is determined by multiplying sheets/Packages/BUNDLE. For example, an order calls for 112 sheets/package. According to the maximum height allowed for a lift. Therefore, multiplying 15 packages X 112 sheets 3D 1680 sheets/bundle.

Centroid:

แปลว่า(english) Similar to the concept of center of gravity, except that it applies to a two dimensional shape rather than an object. For a given shape, the centroid location corresponds to the center of gravity for a thin flat plate of that shape, made from a homogeneous material.

Degree of Freedom:

แปลว่า(english) A displacement quantity which defines the shape and location of an object. In the two dimensional plane, a rigid object has three degrees of freedom: two translations and one rotation. In three dimensional space, a rigid object has six degrees of freedom (three translations and three rotations).

Section Modulus:

แปลว่า(english) A property of a cross sectional shape, which depends on shape, and orientation. Section modulus is usually denoted S, and S = I/c, where I = moment of inertia about an axis through the centroid, and c is the distance from the centroid to the extreme edge of the section.

Gravity:

แปลว่า(english) An attractive force between two objects; each object accelerates at a rate equal to the attractive force divided by the object's mass. Objects near the surface of the earth tend to accelerate toward the earth's center at a rate of ; this value is often called the gravitational constant and denoted as g.

Blasting (Blast Cleaning)

แปลว่า(english) A process for cleaning or finishing metal objects by use of an air blast or centrifugal wheel that throws abrasive particles against the surface of the work pieces. Small, irregular particles of steel or iron are used as the abrasive in grit blasting, and steel or iron balls in shot blasting.

Normal strain:

แปลว่า(english) Strain measuring the intensity of deformation along an axis. Normal strain is usually denoted by . Average normal strain between two points is calculated as (Delta L / L), where L is the original distance between the points, and L is the change in that distance. Normal strain is often simply called strain.

Rotation:

แปลว่า(english) Motion of an object where the path of every point is a circle or circular arc. A rotation is defined by a point and vector which determine the axis of rotation. The direction of the vector is the direction of the axis and the magnitude of the vector is the angle of rotation.

Toxicity

แปลว่า(Environmental Engineering) A U.S. EPA hazardous waste characteristic defined with a rigorous test procedure, the TCLP (for Toxicity Characteristic Leaching Procedure). In the procedure, a waste is extracted for 24 hours with an acetic acid solution. The acid extract is then analyzed for the presence of any of the contaminants listed in the procedure.

A Sheet Metal Screw

แปลว่า(english) Sheet metal screws with (a) sharp-pointed ends; and (b) fewer threads per inch than type AB screws; and (c) deeper threads with bettere gripping power than type AB. The industrial Fasteners Institue incorrectly labes type A an “obsolete” thread though it is universally preferred in 18-8 stainless over type AB, especially by the marine industry.

Blast Furnace 2

แปลว่า(english) A vertical shaft type smelting furnace in which an air blast is used, usually hot, for producing pih iron. The furnace is continuous in operation using iron ore, coke, and limestone as raw materials which are charged at the top while the molten iron and slag are collected at the bottom and are tapped out at intervals.

 ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z