ผลการค้นหา

Brinell Hardness Number

แปลว่า(english) The value of hardness of a metal on an arbitrary scale representing kg/mm2, determined by measuring the diameter of the impression made by a ball of given diameter applied under a known load. Values are expressed in Brinell Hardness Numbers, BHN

Back Rake

แปลว่า(english) The angular surface ground back from the cutting edge of cutting tools. On lathe cutting tools. The rake is positive if the face slopws down from the cutting edge toward the shank, and negative if the face sloopes upward toward the shank.

Z-Mill

แปลว่า(english) The full name for z-mill is Sendzimir mill. A Z-mill operates with a very small diameter work roll, normally about 2 inches, backed up by a number of rolls in a pyramid-shaped stack. This roll set up allows you to exert extremely high forces through the work roll and yet keep the work roll from extreme flexing. The take-up roll on the Z-Mill also exerts a tension on the coil as it comes through the mill. The combination of high pressure and tension makes the mill capable of rolling material thin and flat.

Mixing Speed

แปลว่า(Concrete Engineering) Rate of mixer drum rotation or that of the paddles in a pan, open-top, or trough type mixer, when mixing a batch; expressed in revolutions per minute (rpm) or in peripheral] feet per minute of A point on the circumference at maximum diameter.

Statically determinate:

แปลว่า(english) A statically determinate structure is one where there is only one distribution of internal forces and reactions which satisfies equilibrium. In a statically determinate structure, internal forces and reactions can be determined by considering nothing more than equations of equilibrium.

Equivalent

แปลว่า(Environmental Engineering) The mass of the compound which will produce one mole of available reacting substance. Thus, for an acid, this would be the mass of acid which will produce one mole of H+, for a base, one mole of OH-.

Unit Water Content

แปลว่า(Concrete Engineering) The quantity of water per unit volume of freshly mixed concrete, often expressed as gallons or pounds per cubic yard. This is the quantity of water on which the water cement ratio is based, and does not include water absorbed by the aggregate

Blow Back

แปลว่า(english) A coating defect consisting of a lower coating film weight on the bottom of the coated sheet caused by high velocity air in the oven. Blow back usually occurs with high solids coatings which have little solvent to evaporate and "set" the film.

Linear Elastic:

แปลว่า(english) A force-displacement relationship which is both linear and elastic. For a structure, this means the deformation is proportional to the loading, and deformations disappear on unloading. For a material, the concept is the same except strain substitutes for deformation, and stress substitutes for load.

Backoff

แปลว่าRemoval of part of coil from entry end of unit; may be necessitated by a defect in coil or by a wreck in the mill, etc. Backoff weight is the part of the coil that is removed and not finished/produced.

Pressure:

แปลว่า(english) Pressure is a similar idea to stress, the force intensity at a point, except that pressure means something acting on the surface of an object rather than within the material of the object. When discussing the pressure within a fluid, the meaning is equivalent to stress.

Bent Axis Pumps

แปลว่า(english) In this pump, the pistons are at an angle to the drive shaft and Thrust Plate. The piston block shaft is connected to the drive shaft by a universal joint, not shown. The drive shaft, thrust plate, piston block shaft, and piston block all revolve. The connecting rods are attached to the thrust plate and revolve with it, unlike the swash plate pump where the piston rods slide past a stationary swash plate. The outlet ports are semi-circular holes in the Valve Plate, shown on the far right of the animation on edge and in a head-on view below, right. As the pump revolves, half the pistons suck in fluid as they pass over the intake port. The other pistons discharge their fluid through the outlet port. This pump should be compared to the radial piston pump, swash plate pump, and wobble pump.